Differences

This shows you the differences between two versions of the page.

--- cisco:labs:00100 [2025/12/23 04:20] – Name
+++ cisco:labs:00100 [2025/12/26 17:28] (current) – Name
@@ Line 2: / Line 2: @@
 {{ :cisco:labs:00100.jpg?700 |}}
+  - Complete [[cisco:labs:00000|Lab 00000 Initial Config 2 Routers, IOS-XE]]\\
 ===== Router 1 =====
 <code>en
 conf t
-ip route
+ip route 2.2.2.2 255.255.255.255 12.0.0.2</code>
+===== Router 2 =====
+<code>en
+conf t
+ip route 1.1.1.1 255.255.255.255 12.0.0.1</code>
+===== Verification =====
+<code>r1#ping 2.2.2.2
+Type escape sequence to abort.
+Sending 5, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds:
+!!!!!
+Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/5 ms</code>
+<code>r2#ping 1.1.1.1
+Type escape sequence to abort.
+Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
+!!!!!
+Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/3 ms</code>
+<code>r1#show ip route | b Gate
+Gateway of last resort is not set
+.0.0.0/32 is subnetted, 1 subnets
+C        1.1.1.1 is directly connected, Loopback0
+.0.0.0/32 is subnetted, 1 subnets
+S        2.2.2.2 [1/0] via 12.0.0.2
+.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
+C        12.0.0.0/24 is directly connected, GigabitEthernet1
+L        12.0.0.1/32 is directly connected, GigabitEthernet1</code>
+===== TCL Script =====
+<code>r1#tclsh
+r1(tcl)#foreach ipaddr {
++>(tcl)#12.0.0.2
++>(tcl)#2.2.2.2
++>(tcl)#} { ping $ipaddr }
+Type escape sequence to abort.
+Sending 5, 100-byte ICMP Echos to 12.0.0.2, timeout is 2 seconds:
+!!!!!
+Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
+Type escape sequence to abort.
+Sending 5, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds:
+!!!!!
+Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
+r1(tcl)#tclquit</code>
+<code>r2#tclsh
+r2(tcl)#foreach ipaddr {
++>(tcl)#12.0.0.1
++>(tcl)#1.1.1.1
++>(tcl)#} { ping $ipaddr }
+Type escape sequence to abort.
+Sending 5, 100-byte ICMP Echos to 12.0.0.1, timeout is 2 seconds:
+!!!!!
+Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/2 ms
+Type escape sequence to abort.
+Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
+!!!!!
+Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
+r2(tcl)#tclquit</code>

Tim's Technology Gauntlet Wiki

User Tools

Site Tools

Differences

Page Tools